吸出式干燥的機

◆商品亮點 Product features

※擁有平穩相同的撒氣的壓力和露點

1.吸出塔之較高與長度經實踐結杲精密五金算出，塔床的阻力小，提高了縮減廢氣非常干燥劑5秒的碰觸時候，做到生產設備氣的露點要。

2.30％的低溫干澀劑留量，代替補償的低溫干澀劑的天然脆化，為了保證低溫干澀。

3.大中型散出器，保障氣浪飽滿按照潮濕劑層，徹底消除溝流狀況。

※粉碎氣量不足不低于14％

1.優勝的機筒規劃，包存100％的過濾熱能量，店鋪的熱能量采用增高機體二次利用時段.的機體二次利用氣室溫，提生的設備的解吸效率，使人機體二次利用更切底。

2.變干和重復利用所采用倒置對流傳熱方案怎么寫，濕的空氣穿過干的過濾劑實效果更佳。重復利用氣出口額含濕量操縱在亞過飽和程序，使消音器及排氣口緩沖區無結水之慮。

3.可通過常溫、干燥機的正常運行環境下消費需求調接復蘇氣需水量，確認復蘇暖濕氣流不斷平衡，復蘇壓為低至臨界點。

※常溫、干燥劑的使用使用年限長

1.比較適合的機筒尺寸大小，使氣體利用非常粗糙劑層的水流量和精力始終維持好的感覺，足夠產生非常粗糙劑的耐腐蝕性。

2.合適的機系統搭配，在氣體流動進機筒前，經除油解決直接清理氣體流動中內嘴油物與重生態破壞物，盡量不要變干劑層受生態破壞。

※主設備用了貼近生活高好品質電動四輪及氣動平衡閥和準確的全電子元器件智能控住序序控住器，電腦畫質友愛，自動式連著界面顯示雙塔工程狀況，嵌套循環頻次場地可編，出貨控制10min。閘閥期限歷時50萬次操作。

※封頭內部作冷鍍鋅管防繡治理 ，10年不氧化。

※瑜伽動作精確性、機械性能穩固、操作的簡易，布置不要核心。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆常見技術設備運作 Main technical parameters